{"id":9313,"date":"2023-06-26T18:17:10","date_gmt":"2023-06-26T16:17:10","guid":{"rendered":"https:\/\/finres-sa.com\/produit\/202-ceramic-repair-fluid-kit\/"},"modified":"2025-12-19T14:31:58","modified_gmt":"2025-12-19T13:31:58","slug":"202-ceramic-repair-fluid-kit","status":"publish","type":"product","link":"https:\/\/www.finres-sa.com\/en\/product\/202-ceramic-repair-fluid-kit\/","title":{"rendered":"RESIMAC 202 – Ceramic Repair Fluid (KIT)"},"content":{"rendered":"\t\t
\n\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Resimac 202 Ceramic Repair Fluid is an erosion- and corrosion-resistant product for high-abrasion environments.<\/p>

The product contains hardened ceramic fillers and is ideal for protecting metal surfaces in<\/p>

aggressive environments.<\/p>

– Apply to abrasive-blasted surfaces<\/p>

– Apply Metal Repair Paste 101 or Ceramic Repair Paste 201 to repaired surfaces.<\/p>

– Ideal for protecting metal surfaces in environments with aggressive fluids.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Surface preparation<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Metal substrates – Abrasive blasting

1. All oil and grease must be removed from the surface using a suitable cleaner such as MEK.

2. All surfaces must be blast cleaned to ISO 8501\/4 SA2.5 (SSPC SP10\/ NACE 2) with a minimum profile of 75 microns (3mil) using an angular abrasive. of 75 microns (3mil) using an angular abrasive.

3. Once stripped, the surface must be degreased and cleaned with MEK or a similar product.

4. All surfaces must be coated before corrosion or oxidation occurs.

NOTE: for salt-contaminated surfaces, the substrate must be pressure-washed with clean water and checked for salt contamination.

Please refer to the surface preparation and pre-application guide for further information.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Mix<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

APPLICATION INSTRUCTIONS<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Before mixing, please check the following points:<\/p>

1. The base component is at a temperature of 15-25\u00b0C (60-77F\u00b0).<\/p>

2. Ambient and surface temperature above 10\u00b0C (50F\u00b0).<\/p>

Once these 2 checks have been carried out, mix the product.<\/p>

To mix the complete unit (1kg\/3kg), please follow the instructions below:<\/p>

1. Pour the contents of the Activator unit into the Base container.<\/p>

2. Ensure that as much material as possible is drained from the activator container into the base container.<\/p>

3. Mix the 2 components using the spatula provided.<\/p>

4. Make sure the product is streak-free and uniform in color before applying it to the surface to be repaired.<\/p>

Once mixing has begun, the material must be used within 25 minutes at 20\u00b0C (68F\u00b0).<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

1. Use a short-bristled brush to apply the mixed material, with a bristle length of approx. 2 cm.<\/p>

2. Apply the coating at a wet film thickness of 250-350 microns (10-14mil).<\/p>

3. Particular attention should be paid to detailed areas such as edges, corners and welds, where a brush application per<\/p>

brush application may be necessary.<\/p>

4. Allow the 1st layer of material to harden for approx. 2 hours at 20\u00b0C (68\u00b0F).<\/p>

5. Once the 1st coat has hardened sufficiently, apply a 2nd coat of material to a target thickness of<\/p>

250-350 microns (10-14mil).<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Curing time<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Coating time<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

At 20\u00b0C (68F\u00b0), applied materials must be allowed to harden for the times indicated below before being subjected to the conditions indicated.<\/p>

conditions indicated. These times will be extended at lower temperatures and reduced at higher temperatures: <\/p>

Operating time 25mins<\/p>

Minimum recoat time 2 hours<\/p>

Maximum recoat time 6 hours<\/p>

Full cure 2 days<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Minimum – the applied material can be covered as soon as it is dry to the touch, i.e. approx. 2 hours at 20\u00b0C (68\u00b0F).<\/p>

Maximum – covering time must not exceed 6 hours.<\/p>

Once the maximum recoat time has been exceeded, allow the material to harden before abrading or sandblasting to remove surface contamination.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Color<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Shelf life<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Mixed material – Dark grey, Light grey, Red, Blue<\/p>

Basic component – Dark grey, Light grey, Red, Blue<\/p>

Activator component – Amber liquid<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

5 years if unopened and stored under normal dry conditions (15-30\u00b0C\/ 60-86\u00b0F).<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Technical data and specifications<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

https:\/\/www.resimacsolutions.com\/uploads\/4\/5\/0\/7\/45072315\/202_ceramfluid_tds.rv3.12022019.pdf<\/a><\/p>

https:\/\/www.resimacsolutions.com\/uploads\/4\/5\/0\/7\/45072315\/202_ps.rv4.22052019.pdf<\/a><\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t","protected":false},"excerpt":{"rendered":"

A two-component, solvent-free epoxy repair fluid containing hardened ceramic particles for exceptional abrasion resistance.
\nThe product can be used to resurface worn or damaged metal surfaces subject to \u201cfluid erosion and corrosion:
\n– Eroded pump casings and impellers
\n– Eroded filter surfaces
\n– Corroded tube sheets, end plates, and water boxes
\n– Internal surfaces of pipes and elbows
\n– Eroded bow thruster tunnels and coatings\u201d
\n– Leading edge of rudders<\/p>\n","protected":false},"featured_media":7861,"template":"","meta":[],"product_brand":[],"product_cat":[385,1664],"product_tag":[656,611,613,559,416],"class_list":{"0":"post-9313","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-epoxy-en","7":"product_cat-rapid-repair-and-coating-kit","8":"product_tag-abrasion-en","9":"product_tag-industry","10":"product_tag-metal-en","11":"product_tag-protection-en","12":"product_tag-repair","14":"first","15":"instock","16":"taxable","17":"shipping-taxable","18":"purchasable","19":"product-type-variable"},"_links":{"self":[{"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product\/9313","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/types\/product"}],"version-history":[{"count":1,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product\/9313\/revisions"}],"predecessor-version":[{"id":34585,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product\/9313\/revisions\/34585"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/media\/7861"}],"wp:attachment":[{"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/media?parent=9313"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product_brand?post=9313"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product_cat?post=9313"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.finres-sa.com\/en\/wp-json\/wp\/v2\/product_tag?post=9313"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}